Influence of Heat Treatment Modes on the Structure and Properties of Large-Sized Products of Advanced Aviation Equipment Made of Alloys of the Al-Zn-Mg-Cu System
https://doi.org/10.23947/2541-9129-2024-8-3-78-87
EDN: NTBOKI
Abstract
Introduction. High-strength aluminum-based alloys of the Al-Zn-Mg-Cu alloying system are commonly used in aircraft manufacturing. However, there is a need to address the issue of achieving the desired level of mechanical properties in large-scale parts made from these alloys during heat treatment. Additionally, studies on the evaluation of corrosion resistance during heat treatment are also essential. The aim of this work was to determine the modes of heat treatment to achieve the necessary values of mechanical properties and resistance to corrosion cracking of parts made of large-sized deformed blanks of alloys of the Al-Zn-Mg-Cu alloying system.
Materials and Methods. The research was conducted on parts made from forged 1933 alloy forgings and B93pch stamped blanks. The influence of heat treatment on the mechanical properties (strength, ductility, hardness) and microstructure, as well as electrical conductivity, was determined. Tensile tests were carried out both on samples subjected to heat treatment after cutting from forgings and stamped blanks, and on samples cut from massive templets that were heat treated together with the products. Electrical conductivity allowed us to assess the level of solid solution supersaturation and predict resistance to corrosion cracking.
Results. The results of the study showed the necessity of a differentiated approach to assigning the duration of aging stages, depending on the alloy grade, configuration, and dimensions of the products, as well as the requirements for the level of properties. Variants and modes of heat treatment were proposed for products made from alloys 1933 and B93pch, providing the necessary level of mechanical properties and resistance to corrosion cracking.
Discussion and Conclusion. Cases of inconsistency in strength properties in the longitudinal and transverse (in width) directions of the fiber of parts made from large-sized blanks of alloys 1933 and B93pch have been established. Modes and options for heat treatment of parts were proposed, allowing the achievement of the required values of mechanical properties and corrosion resistance. This provides for a halving of the aging time for alloy 1933 or an increase of 25% for alloy B95pch.
About the Authors
V. S. MuratovRussian Federation
Vladimir S. Muratov, Dr. Sci. (Eng.), Professor of the Department of Metallurgy, Powder Metallurgy, Nanomaterials
244, Molodogvardeyskaya St., Samara, 443100
N. S. Yakimov
Russian Federation
Nikolai S. Yakimov, Cand. Sci. (Eng.), Leading Engineer
55, Zavodskoe highway, Samara, 443009
References
1. Mechanical Engineering. Non-Ferrous Metals and Alloys. Composite Metal Materials. Encyclopedia. In 40 vol. Vol. II–3. Moscow: Mashinostroenie; 2001. 880 p. (In Russ.)
2. Kablov EN. Strategical Areas of Developing Materials and Their Processing Technologies for the Period up to 2030. Aviation Materials and Technologies. 2012;(S):7–17. (In Russ.)
3. Kablov EN, Antipov VV, Odolodkova YuS, Odolodkov MS. Experience and Application Prospects of Aluminum-Lithium Alloys in Aircraft and Space Technology. Metallurg. 2021;(1):62–70. URL: https://library.bmstu.ru/Publications/Home/AuthorPublications/c00e1744-db59-4d2f-9f79-1e9e757d5105 (accessed: 29.04.2024). (In Russ.)
4. Fridlyander IN. Memories of the Creation of Aerospace and Nuclear Technology from Aluminum Alloys. 2-nd ed. Moscow: Nauka; 2006. 275 p. URL: https://elib.biblioatom.ru/text/fridlyander_vospominaniya_2006/p12/ (accessed: 29.04.2024). (In Russ.)
5. Antipov VV, Senatorova OG, Tkachenko EA, Vakhromov PO. Aluminium Wrought Alloys. Aviation Materials and Technologies. 2012;(S):167–182. (In Russ.)
6. Antipov VV, Senatorova OG, Sidelnikov VV, Popov VI, Blinova NE. Development and Application of HighStrength Alloys of the Al-Zn-Mg-Cu-Zr System for Aviation and Rocket Technology. In: Proceedings of the International scientific and technical conference “Development of the fundamentals of materials science of light alloys and composite materials based on them for the creation of aerospace and nuclear engineering products”. Moscow: AllRussian Scientific Research Institute of Aviation Materials of the National Research Center “Kurchatov Institute”; 2013. P. 51. (In Russ.)
7. Kablov EN. Quality Control of Materials is a Guarantee of the Safety of Aviation Equipment Operation. Aviation Materials and Technologies. 2001:(1);3–8. (In Russ.)
8. Senatorov OG, Antipov VV, Bronz AV, Somov AV, Serebrennikova NYu. High-Strength and Super HighStrength Conventional Al-Zn-Mg-Cu System-Based Alloys, Their Role in Engineering and Possibility of Development. Tekhnologiya legkikh splavov. 2016;4:43–49. (In Russ.)
9. Kai Wen, Yunqiang Fan, Guojun Wang, Longbin Jin, Xiwu Li, Zhihui Li, et al. Aging Behavior and Precipitate Characterization of a High Zn-Containing Al–Zn–Mg–Cu Alloy with Various Tempers. Materials & Design. 2016;101:16–23. http://doi.org/10.1016/j.matdes.2016.03.150
10. Kablov EN. Innovative Developments of FSUE “VIAM” SSC of RF on Realization of “Strategic Directions of the Development of Materials and Technologies of Their Processing for the Period until 2030”. Aviation Materials and Technologies. 2015;1(34):3–33. URL: https://journal.viam.ru/ru/system/files/uploads/pdf/2015/2015_1_1_1.pdf (accessed: 29.04.2024). (In Russ.)
11. Antipov VV. Prospects for Development of Aluminium, Magnesium and Titanium Alloys for Aerospace Engineering. Aviation Materials and Technologies. 2017;(S):186–194. https://doi.org/10.18577/2071-9140-2017-0-S-186-194 (In Russ.)
12. Kablov EN. New Generation Materials and Technologies for Their Digital Processing. Herald of the Russian Academy of Sciences. 2020;90(4):331–334. https://doi.org/10.31857/S0869587320040052 (In Russ.)
13. Fridlyander IN. Modern Aluminum, Magnesium Alloys and Composite Materials Based on Them. Metallovedenie i termicheskaya obrabotka metallov. 2002;(7):24–29. (In Russ.)
14. Nechaykina TA, Blinovа NE, Ivanov AL, Kozlova OYu, Kozhekin AE. Research of the Effect of Homogenization and Quench Hardening Modes on the Structure and Mechanical Properties of Retail Rings From Alloy В95o.ch.-T2. Proceedings of VIAM. 2018;10(70):27–36. https://doi.org/10.18577/2307-6046-2018-0-10-27-36 (In Russ.)
15. Senatorova OG, Serebrennikova NYu, Antipov VV, Ivanov AL, Popov VI. Investigation of the Structure and Properties of an 80 mm Thick Plate Made of B95 p.chT2 Alloy. Tekhnologiya legkikh splavov. 2016;(2):37–42. (In Russ.)
16. Nechaikina TA, Oglodkov MS, Ivanov AL, Kozlova OYu, Yakovlev SI, Shlyapnikov MA. Features of Quenching of Wide Cladding Clad Sheets Made of Aluminum Alloy B95p.ch on a Continuous Heat Treatment Line. Proceedings of VIAM. 2021;(11(105)):25–33. https://doi.org/10.18577/2307-6046-2021-0-11-25-33 (In Russ.)
17. Ovsyannikov BV. Beware of Grain Refinement. Materials Science Forum. 2014;794–796:143–148. http://dx.doi.org/10.4028/www.scientific.net/MSF.794-796.143
18. Leonov VV, Nikiforov AG, Kovaleva AA. Identification of Correlations between Physical Properties of Aluminum Alloys. Fundamental research. 2017;(7):44–48. URL: https://elibrary.ru/item.asp?id=29771980&ysclid=lxeg34pp2m868169526 (In Russ.)
Review
For citations:
Muratov V.S., Yakimov N.S. Influence of Heat Treatment Modes on the Structure and Properties of Large-Sized Products of Advanced Aviation Equipment Made of Alloys of the Al-Zn-Mg-Cu System. Safety of Technogenic and Natural Systems. 2024;(3):78-87. https://doi.org/10.23947/2541-9129-2024-8-3-78-87. EDN: NTBOKI